Rig Breakdown: 20x20 ModX Softbox

Legacy Grip

Blog

Gallery

Courses

shop

Legacy Grip

Blog

Gallery

Courses

shop

Legacy Grip

Blog

Gallery

Courses

shop

rig breakdown

Title:

20x20 ModX Softbox

Commercial

about the rig

20x20x4 softbox made out of Modulus-X Mx|66|. I find the rigidity of the modulus-x allows you to tilt the box and aim it more aggressively. It’s slimmer and a bit more versatile than a 12” box truss build.

The truss provides a strong support structure for the entire build. We set this box up with a center rib for the cross pipe support. Gaffer Tony Jou employed the use of 8 skypanel S60’s to evenly fill the box. We finished the box up with some full grid diffusion and duvetyne sides. The box hung on 4 1/2 ton chain motors.

Behind the Scenes

Lighting

Overhead Rigging

key grip

Brendan Riel

the crew

DP:

Zoë Simone-Yi

Grip Crew:

Logan Alesso, Eric Fowler, Connor Colby, Vic Roca, Daniel Kusenda, Erik Covarrubias, Johnathan Gonzalez, Jacob Senn, DJ Meyer

built with

Modulus-X™ Truss, LA Rag House, Hollaender, Modern Studio Equipment

by:

Brendan Riel

similar posts

rig breakdown

20x20 Flyswatter

by:

Brendan Riel

My standard swatter built. Triangle truss with 1 steel. 8’ verticals for the goalpost with a 5’ horizontal. Wigs from the bucket to the tri truss. Kickers on the goalpost. 20’ kickers from the goalpost to the 20x20 frame. 2x belly lines to finish it off.

Read >

rig breakdown

20x20 Flyswatter

by:

Brendan Riel

Read >

Case Study

Title

by:

Brendan Riel

this is about

Read >

rig breakdown

ModX Rolling Soft Toplight

by:

Brendan Riel

We built this mobile toplight softbox using 6" ModX truss to serve four different sets inside a tight studio space with limited overhead clearance. The goal was to keep costs down and avoid building duplicate overhead rigs or ground units for each set. So, we designed a rolling, double-layered softbox that could easily move from set to set—and double as an in-frame ceiling piece when needed.

The structure measured 14’x14’ OD and held two 12x12 frames: one with 1/2 grid and one with bleached muslin. The bleached muz was rigged with a pulley system, allowing us to raise or drop the rag when we needed to bring it into the scene as a ceiling element. We punched LiteTile through both rags for soft, consistent coverage.

For mobility, we mounted the whole rig on C&C Studio Services tri-casters.

Read >

project BTS

Seamless Muslin Softbox

by:

Brendan Riel

8’x25’x4’ seamless bleached muslin softbox provided most of our soft top daylight ambiance for this spot. ModX top frame with pipe bottom frame. We wrapped the bottom pipe with plastic to protect the muslin from dirt. Seamless was important for car reflections. We baffled the inside of the box with 1/4 grid for added softness.

We helped art hang an 18’ tall 60’ length translight with some truss and motors. Went motors down so we wouldn’t have to run too much cable and picked to beams above with beam clamps.

We planned on doing everything with truss and motors but had to cut some because of budgetary reasons. So we went old fashioned with 2 runs of ladder truss, pipe and pulleys for more lighting points. The pulleys just served as line redirects and provided no mechanical advantage.

Read >

project BTS

Seamless Muslin Softbox

by:

Brendan Riel

We helped art hang an 18’ tall 60’ length translight with some truss and motors. Went motors down so we wouldn’t have to run too much cable and picked to beams above with beam clamps.

Read >