rig breakdown
rig breakdown
Title:
Title:
Lazy Susan Rig
Commercial
Commercial
Commercial
Commercial
about the rig
Modulus-X 6” lazy susan rig built with truss from Division Rentals in Los Angeles. Their custom lazy susan bearing only spins in the middle and keeps the top and bottom plates static.
Camera Movement
key grip
Brendan Riel
the crew
DP:
Josh Saideman
Grip Crew:
Connor Colby, Vic Roca, Nick Zajic, Thorn Shaffer
built with
Modulus-X™ Mx|66|, Modern Studio Equipment
by:
Brendan Riel
similar posts
similar posts
rig breakdown
20x20 Flyswatter
by:
Brendan Riel
My standard swatter built. Triangle truss with 1 steel. 8’ verticals for the goalpost with a 5’ horizontal. Wigs from the bucket to the tri truss. Kickers on the goalpost. 20’ kickers from the goalpost to the 20x20 frame. 2x belly lines to finish it off.
rig breakdown
20x20 Flyswatter
by:
Brendan Riel
My standard swatter built. Triangle truss with 1 steel. 8’ verticals for the goalpost with a 5’ horizontal. Wigs from the bucket to the tri truss. Kickers on the goalpost. 20’ kickers from the goalpost to the 20x20 frame. 2x belly lines to finish it off.
rig breakdown
20x20 Flyswatter
by:
Brendan Riel
My standard swatter built. Triangle truss with 1 steel. 8’ verticals for the goalpost with a 5’ horizontal. Wigs from the bucket to the tri truss. Kickers on the goalpost. 20’ kickers from the goalpost to the 20x20 frame. 2x belly lines to finish it off.
rig breakdown
20x20 Flyswatter
by:
Brendan Riel
My standard swatter built. Triangle truss with 1 steel. 8’ verticals for the goalpost with a 5’ horizontal. Wigs from the bucket to the tri truss. Kickers on the goalpost. 20’ kickers from the goalpost to the 20x20 frame. 2x belly lines to finish it off.
rig breakdown
ModX Rolling Soft Toplight
by:
Brendan Riel
We built this mobile toplight softbox using 6" ModX truss to serve four different sets inside a tight studio space with limited overhead clearance. The goal was to keep costs down and avoid building duplicate overhead rigs or ground units for each set. So, we designed a rolling, double-layered softbox that could easily move from set to set—and double as an in-frame ceiling piece when needed.
The structure measured 14’x14’ OD and held two 12x12 frames: one with 1/2 grid and one with bleached muslin. The bleached muz was rigged with a pulley system, allowing us to raise or drop the rag when we needed to bring it into the scene as a ceiling element. We punched LiteTile through both rags for soft, consistent coverage.
For mobility, we mounted the whole rig on C&C Studio Services tri-casters.
rig breakdown
ModX Rolling Soft Toplight
by:
Brendan Riel
We built this mobile toplight softbox using 6" ModX truss to serve four different sets inside a tight studio space with limited overhead clearance. The goal was to keep costs down and avoid building duplicate overhead rigs or ground units for each set. So, we designed a rolling, double-layered softbox that could easily move from set to set—and double as an in-frame ceiling piece when needed.
The structure measured 14’x14’ OD and held two 12x12 frames: one with 1/2 grid and one with bleached muslin. The bleached muz was rigged with a pulley system, allowing us to raise or drop the rag when we needed to bring it into the scene as a ceiling element. We punched LiteTile through both rags for soft, consistent coverage.
For mobility, we mounted the whole rig on C&C Studio Services tri-casters.
rig breakdown
ModX Rolling Soft Toplight
by:
Brendan Riel
We built this mobile toplight softbox using 6" ModX truss to serve four different sets inside a tight studio space with limited overhead clearance. The goal was to keep costs down and avoid building duplicate overhead rigs or ground units for each set. So, we designed a rolling, double-layered softbox that could easily move from set to set—and double as an in-frame ceiling piece when needed.
The structure measured 14’x14’ OD and held two 12x12 frames: one with 1/2 grid and one with bleached muslin. The bleached muz was rigged with a pulley system, allowing us to raise or drop the rag when we needed to bring it into the scene as a ceiling element. We punched LiteTile through both rags for soft, consistent coverage.
For mobility, we mounted the whole rig on C&C Studio Services tri-casters.
rig breakdown
ModX Rolling Soft Toplight
by:
Brendan Riel
We built this mobile toplight softbox using 6" ModX truss to serve four different sets inside a tight studio space with limited overhead clearance. The goal was to keep costs down and avoid building duplicate overhead rigs or ground units for each set. So, we designed a rolling, double-layered softbox that could easily move from set to set—and double as an in-frame ceiling piece when needed.
The structure measured 14’x14’ OD and held two 12x12 frames: one with 1/2 grid and one with bleached muslin. The bleached muz was rigged with a pulley system, allowing us to raise or drop the rag when we needed to bring it into the scene as a ceiling element. We punched LiteTile through both rags for soft, consistent coverage.
For mobility, we mounted the whole rig on C&C Studio Services tri-casters.
project BTS
Seamless Muslin Softbox
by:
Brendan Riel
8’x25’x4’ seamless bleached muslin softbox provided most of our soft top daylight ambiance for this spot. ModX top frame with pipe bottom frame. We wrapped the bottom pipe with plastic to protect the muslin from dirt. Seamless was important for car reflections. We baffled the inside of the box with 1/4 grid for added softness.
We helped art hang an 18’ tall 60’ length translight with some truss and motors. Went motors down so we wouldn’t have to run too much cable and picked to beams above with beam clamps.
We planned on doing everything with truss and motors but had to cut some because of budgetary reasons. So we went old fashioned with 2 runs of ladder truss, pipe and pulleys for more lighting points. The pulleys just served as line redirects and provided no mechanical advantage.
project BTS
Seamless Muslin Softbox
by:
Brendan Riel
8’x25’x4’ seamless bleached muslin softbox provided most of our soft top daylight ambiance for this spot. ModX top frame with pipe bottom frame. We wrapped the bottom pipe with plastic to protect the muslin from dirt. Seamless was important for car reflections. We baffled the inside of the box with 1/4 grid for added softness.
We helped art hang an 18’ tall 60’ length translight with some truss and motors. Went motors down so we wouldn’t have to run too much cable and picked to beams above with beam clamps.
We planned on doing everything with truss and motors but had to cut some because of budgetary reasons. So we went old fashioned with 2 runs of ladder truss, pipe and pulleys for more lighting points. The pulleys just served as line redirects and provided no mechanical advantage.
project BTS
Seamless Muslin Softbox
by:
Brendan Riel
8’x25’x4’ seamless bleached muslin softbox provided most of our soft top daylight ambiance for this spot. ModX top frame with pipe bottom frame. We wrapped the bottom pipe with plastic to protect the muslin from dirt. Seamless was important for car reflections. We baffled the inside of the box with 1/4 grid for added softness.
We helped art hang an 18’ tall 60’ length translight with some truss and motors. Went motors down so we wouldn’t have to run too much cable and picked to beams above with beam clamps.
We planned on doing everything with truss and motors but had to cut some because of budgetary reasons. So we went old fashioned with 2 runs of ladder truss, pipe and pulleys for more lighting points. The pulleys just served as line redirects and provided no mechanical advantage.
project BTS
Seamless Muslin Softbox
by:
Brendan Riel
8’x25’x4’ seamless bleached muslin softbox provided most of our soft top daylight ambiance for this spot. ModX top frame with pipe bottom frame. We wrapped the bottom pipe with plastic to protect the muslin from dirt. Seamless was important for car reflections. We baffled the inside of the box with 1/4 grid for added softness.
We helped art hang an 18’ tall 60’ length translight with some truss and motors. Went motors down so we wouldn’t have to run too much cable and picked to beams above with beam clamps.
We planned on doing everything with truss and motors but had to cut some because of budgetary reasons. So we went old fashioned with 2 runs of ladder truss, pipe and pulleys for more lighting points. The pulleys just served as line redirects and provided no mechanical advantage.
By subscribing you agree to with our privacy policy and provide consent to receive updates from our company.
Legacy Grip 2025 All Rights Reserved
By subscribing you agree to with our privacy policy and provide consent to receive updates from our company.
Legacy Grip 2025 All Rights Reserved
By subscribing you agree to with our privacy policy and provide consent to receive updates from our company.
Legacy Grip 2025 All Rights Reserved
By subscribing you agree to with our privacy policy and provide consent to receive updates from our company.
Legacy Grip 2025 All Rights Reserved